TL;DR
Dominic Chinea is adapting a 1917 Liberty V12 aircraft engine for an Edwardian-style race car, but welding its cast-aluminum block has proved difficult. After repeated cracks and contaminated welds, he sought help through his YouTube channel and received repair suggestions from viewers with relevant experience.
Dominic Chinea has turned to viewers around the world for help repairing a 1917 Liberty V12 aircraft engine, after attempts to weld its cast-aluminum block into a shorter form led to contamination and cracks. The former BBC show The Repair Shop cast member is adapting the engine for an Edwardian-style race car, and the response to his request has brought advice from welders and other experienced tradespeople into the project.
Get business pricing on garage and car supplies
- Business-only prices and quantity discounts
- Tax-exempt purchasing
- Multiple users, one account, clear invoices
Chinea is combining the Liberty engine with a 1912 Rochet-Schneider chassis to build an aero-engined racing car intended for vintage competition, specifically the Goodwood Members’ Meeting. The project is meant to use period-correct components and techniques, according to the report. Because the V12 was too long for the chassis, Chinea decided to shorten it by cutting the engine and rejoining the pieces to create a V8 configuration.
The engine block consists of an upper section containing the cylinders and a lower section containing the crankcase and sump. In the video covered by The Drive, Chinea focuses on welding the upper half. The block’s cast aluminum, made to 1910s-era standards, presented a particular challenge: impurities rose to the surface during welding and contaminated the welds. Sections cracked as he worked on the joint from the outside and then the more confined inside.
After early attempts failed, Chinea tried using wet rags to cool the metal while welding very short sections at a time. When problems persisted and he was running out of welding gas, he asked viewers for suggestions. The report says contributors included a Swiss welder experienced with 1920s Bugattis and Bentleys, an 80-year-old former locomotive engineer and a former hydraulic-ram fabricator. Their ideas included addressing aluminum oxide, drilling small holes to limit crack propagation and building up material with smaller tack-style welds.
Online Advice Reaches the Workshop
The exchange shows how a specialist restoration project can draw on knowledge that may be difficult to find in a manual, particularly when the machinery predates modern manufacturing standards. Chinea is working with century-old cast aluminum, and the report describes failures that required practical troubleshooting rather than a straightforward repair procedure.
The responses do not establish that the proposed methods have solved the problem. Their immediate significance is that people with different kinds of hands-on experience offered specific, testable suggestions after Chinea’s own attempts produced cracks. For viewers, the project also makes the trial-and-error behind historic-engine restoration visible, rather than presenting the repair as a completed result.
Products Worth Considering

Milwaukee M12 FUEL 12V 1/4-Inch Hex Impact Driver Kit

DEWALT 20V MAX XR Brushless Hammer Drill and Impact Driver Combo Kit with Two 4 Ah Batteries and 4 A Charger (DCK2112QQ2)

Vantrue N4S 3-Channel Dash Cam with STARVIS 2 Night Vision
As an affiliate, we earn on qualifying purchases.
From Warplane Engine to Racer
Liberty engines were mass-produced for the wartime aviation effort, and surplus engines became available after World War I. The Drive reports that racers valued aircraft engines for their power relative to weight, and that leftover Liberty engines could be obtained for automotive projects. Chinea’s build follows that period practice by pairing an aircraft engine with an older car chassis.
The proposed car draws on the Edwardian-era British racing specials, which combined components for competition rather than relying on a standard production-car arrangement. Chinea’s project uses a 1912 chassis and a 1917 engine; shortening the V12 is central to fitting the engine to the chosen chassis. The stated target is the Goodwood Members’ Meeting, though the source does not give a completion date or confirm that the car has been accepted for an event.
“There’s no instruction manual for repairing century-old hardware, let alone modifying it for different purposes.”
— The Drive, describing Chinea’s project
The Engine’s Repair Status
The source describes a breakthrough in Chinea’s approach, but does not establish that the block has been successfully welded into a durable, usable V8. It also does not report whether the advice about oxide, drilled holes or smaller welds has been tested, or whether any resulting repair has been inspected or run.
The report focuses on the top half of the engine block. The state of the lower half, the rest of the engine’s assembly and the car’s overall progress are not detailed. It is also unclear whether the finished car will meet the event’s requirements or when it might be ready for the Goodwood Members’ Meeting.
Further Welding and Testing
The next reported challenge is completing the block repair and determining whether the welds can hold without further cracking. Chinea’s video documents the process, while the viewer comments offer approaches he may assess; the source does not say which suggestions he will adopt.
After the upper section is repaired, the engine and car would still need further work before the project could reach its stated vintage-racing goal. No timetable, testing plan or event entry is given in the report, so the project’s eventual completion and participation remain unconfirmed.
Key Questions
Who is repairing the Liberty engine?
Dominic Chinea, a former set designer and cast member of the BBC program The Repair Shop, is documenting the work on his YouTube channel.
Why is the engine being shortened?
The 1917 Liberty V12 is too long for the 1912 Rochet-Schneider chassis Chinea is using. He plans to cut and rejoin it in a V8 configuration for an Edwardian-style racing car.
What is making the welding difficult?
The engine block is made of old cast aluminum. According to The Drive, impurities rise to the surface during welding, contaminating the welds and contributing to cracks.
What advice did viewers offer?
Suggestions reported by The Drive included dealing with excess aluminum oxide, drilling small holes to help stop cracks spreading and using smaller tack-style welds to build up material. The report does not confirm that these methods have resolved the problem.
Will the car race at Goodwood?
The Goodwood Members’ Meeting is the project’s stated vintage-racing target, but the source does not confirm an entry, a completion date or that the car will be ready to compete.
Source: thedrive.com
